- 您现在的位置：买卖IC网 > Sheet目录537 > XT09-PKI-EA-NA (Digi International/Maxstream)MODEM RF 900MHZ 1W ETHER INT
9XTend ‐ PKG ‐ E? ? Ethernet ? RF ? Modem ? – ? Product ? Manual ? v2.x4x ? [2007.01.04]
NB (Parity) Command
<Serial Interfacing> The NB command is used to
select/read the parity settings of the RF modem
for UART communications.
AT Command: ATNB
Binary Command: 0x23 (35 decimal)
Parameter Range: 0 - 4
Parameter
0
1
2
3
4
Configuration
8-bit (no parity or
7-bit (any parity)
8-bit even
8-bit odd
8-bit mark
8-bit space
Default Parameter Value: 0
Number of bytes returned: 1
PB (Polling Begin Address) Command
<Networking & Security> PB command is used to
set/read the modem’s Polling Begin Address - the
first address polled Polling Mode is enabled.
Polling Operations: The ‘Polling Base’ (MD = 3)
cycles through a sequential range of addresses,
polling each ‘Polling Remote’ (MD = 4). The base
then waits for a response & proceeds to the next
‘Polling Remote’. Each ‘Polling Remote’ responds
by sending the data from the Data In buffer fol-
lowing the RB & RO parameters. When there is no
AT Command: ATPB
Binary Command: 0x45 (69 decimal)
Parameter Range: 0 - 0xFFFF
Default Parameter Value: 0
Number of bytes returned: 2
Minimum Firmware Version Required: 2.x20
Related Commands: MD (RF Mode), PE (Polling
End Address), PD (Minimum Polling Delay)
eligible data to send, the ‘Polling Remote’ will not respond. The ‘Polling Base’ will move to the next
address in the polling sequence after a short delay.
PD (Minimum Polling Delay) Command
<Networking & Security> The PD command is
used to set/read Polling Delay (Base, MD=3) or
Polling Timeout (Remote, MD=4).
Polling Delay (Base) is the time between polling
cycles. The Polling Base will start the polling cycle
after sending the first poll. After the polling cycle
has completed, the timer is restarted.
Polling Timeout (Remote) is the amount of time
the remote unit will hold data from the serial port
before discarding it. Data entered within the PD
time of the poll is transmitted and not discarded.
PE (Polling End Address) Command
<Networking & Security> PE command is used to
set/read the modem’s Polling End Address - the
last address polled when Polling Mode is enabled.
Polling Operations : The ‘Polling Base’ (MD = 3)
cycles through a sequential range of addresses,
polling each ‘Polling Remote’ (MD = 4). The base
then waits for a response & proceeds to the next
‘Polling Remote’. Each ‘Polling Remote’ responds
by sending data from the DI buffer following the
RB & RO parameters. When there is no eligible
AT Command: ATPD
Binary Command: 0x47 (71 decimal)
Parameter Range: 0 - 0xFFFF
(Base: [x 1ms], Remote: [x 10ms])
Default Parameter Value: 0
Number of bytes returned: 2
Minimum Firmware Version Required: 2.x20
Related Commands: MD (RF Mode), PB (Polling
Begin Address), PE (Polling End Address)
AT Command: ATPE
Binary Command: 0x46 (70 decimal)
Parameter Range: 0 - 0xFFFF
Default Parameter Value: 0
Number of bytes returned: 2
Minimum Firmware Version Required: 2.x20
Related Commands: MD (RF Mode), PB (Polling
Begin Address), PD (Minimum Polling Delay)
data to send, the ‘Polling Remote’ will not respond. The ‘Polling Base’ will move to the next address
in the polling sequence after a short delay.
? ? 2007 ? MaxStream, ? Inc., ? Confidential ? & ? Proprietary ?‐? All ? Rights ? Reserved ?
????? 33
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
XT09-SI
MODULE RF 900MHZ 1W 115K W/RPSMA
XU-A11
X-STICK 2.4GHZ USB TO XBEE
XV-8000CB :3 50.3000KHZ+/-60DPS
AUTOMOTIVE GYRO SENSOR +/-60DPS
YB03WKW01-6B-JB
INDICATOR PB RECT WHT LED ILLUM
YGM1 C518
THERM PTC MINI-BEAD 3MM 180C
YQD120N0006
THERMISTOR PTC OCP 6 OHM 25C
Z4D-A01
PHOTO SENSOR 7.5MM REFLECT TYPE
ZALM-301-1C-B
RF TRANSCEIVER 100MW MMCX W/CONN
相关代理商/技术参数
XT09-PKI-E-NA
功能描述:射频模块 9XTend 1W Ethernet w/o accessories Intl
RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm
XT09-PKI-R
功能描述:射频模块 9XTend 1W RS232/485 w/o accessories
RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm
XT09-PKI-RA
功能描述:射频模块 900MHz - Xtend software setable
RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm
XT09-PKI-RA-NA
功能描述:射频模块 9XTend 1W RS232/485 w/accessories no AES
RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm
XT09-PKI-RDA
功能描述:射频模块 XTend-PKG 900 MHz IndRS-232class1/div2
RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm
XT09-PKI-R-NA
功能描述:射频模块 9XTend 1W RS232/485 w/o accessories Intl
RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm
XT09-PKI-R-NL
制造商:Digi International Inc 功能描述:MODEM RF 900MHZ 9600/11
XT09-PKT-R
功能描述:MODEM RF 900MHZ RS232/485 RoHS:是 类别:RF/IF 和 RFID >> RF 接收器、发射器及收发器的成品装置 系列:XTend™ 标准包装:5 系列:MultiModem® iCell 功能:收发器，HSPA，调制解调器 调制或协议:GPRS，GSM，EDGE 频率:850MHz，900MHz，1.8GHz，1.9GHz 应用:- 接口:RS-232，USB 灵敏度:- 功率 - 输出:- 数据传输率 - 最大:7.2 Mbps 特点:- 电源电压:9 V ~ 32 V，USB 其它名称:881-1125